Ruffled Business Card Holder Tutorial and GIVEAWAY!

Ruffled Business Card Holder by the Crafty Cupboard
It has been a while since the Business Card Holder has made its way to its own blog post!  As I was listing my last batch into my Etsy shop, I thought it might be time to switch things up a bit and add a little bit more pizzazz to the ‘ol card holder.  And, a ruffle was born!
Ruffled Business Card Holder Materials
For this card holder, you will use the same steps as the original, so go there for some refreshing first.  For the basic holder, you need:

  • 5 1/2” x 4 1/2” outer fabric
  • 5 1/2” x 4 1/2” lining fabric
  • 5 1/2” x 4 1/2” fusible fleece interfacing
  • TWO 2 1/2” x 4 1/2” pocket pieces, with one side hemmed
  • button
  • elastic closure
  • The only different thing is the ruffle, a 1 1/2” x 11” piece of fabric.  I serged the edges of mine so it wouldn’t unravel.

Ruffle Ruffles
First, run two rows of gathering stitches down your ruffle fabric.  Set your stitch length to the longest possible, and don’t backstitch. Pull on the BOTTOM threads to gather it to 5 1/2”.
Pin Ruffle to Fabric
Pin the ruffled fabric down the center of your outer fabric piece.
Stitch Ruffle
Set your stitch length back to its regular setting, and stitch your ruffle down to your outer fabric piece.
Remove Gathering Stitches
When you are done sewing the ruffle down, gently pull on the BOTTOM gathering threads again until they pull all they way out of your fabric.
Fusible Fleece
Iron your fusible fleece to the wrong side of your outer fabric.  I set my fusible fleece down adhesive side up, then lay my outer fabric down on top of it with the right side up and then iron it; the photo is just showing the fleece ironed to the fabric.  Make sure you don’t iron too many kinks into the ruffle :)
Lining pockets and loop
Prepare your lining by laying the pockets on the ends and pinning in place.  I also save a step now and pin my elastic to the lining and pocket at this point.
RST and pin
Pin your prepared lining to your ruffled outer fabric, right sides together.
Leave opening
Stitch around the perimeter at a scant 1/4”, leaving a space for turning on one of the longer sides, between the pockets.  I tend to sew a few extra rows over the elastic to secure it.
Trim edges and elastic
Trim the edges and corners to eliminate bulk when you turn it, and make sure you cut off the extra elastic.
Turn and finish corners
Turn the card holder right side out and poke your corners to a nice square using a blunt pencil or a chopstick, or the end of a paintbrush like I did. Iron it nice and flat.
Iron and top stitch
Top-stitch around the entire card holder close to the edge (think 1/8” or smaller), making sure you close the hole left for turning in the process.
Top view
Give it one more pressing once you have top stitched the card holder so it is nice and crisp, and to keep those ruffles tamed.
Sew on Button
Attach your button by sneaking your needle and thread on the inside of the interior pocket so you don’t stitch the pocket shut.
Card Holder
Fill with business cards (20-25 standard cards per pocket) and enjoy!
Finished Ruffled Card Holder
Now, because I think you are all so awesome and I know there are lots of reasons coming up to have a business card holder (I actually use mine for gift cards and store loyalty cards most of the time), I am going to give this one away!  Do you want it?  YES YOU DO!  Let’s make this a FLASH giveaway!  This one only lasts for today, and sorry, US shipping addresses only!  Ends at midnight, PST.
Just leave a comment :)
(I am going to be doing lots of Flash Giveaways this year, sometimes small items, sometimes bigger.  If you want to stay updated, subscribe via RSS or Google Friend Connect <–on the sidebar, “LIKE” my page on Facebook, or Follow me on Twitter and Pinterest!)

Back to Blog


Leave a reply

CommentLuv badge

Back to Blog